Size of trading unit: 0,25L; 1L
For refreshing and maintenance of all natural and white indoor oil treated wood surfaces.
Consumption: Depending on the area of application and absorptivity of the substrate: 10-20 g/sqm per application / 1 litre is sufficient for circa 50-100 sqm.
Warning: Last items in stock!
For refreshing and maintenance of all natural and white indoor oil treated wood surfaces
OLI-NATURA Care Oil is specifically designed for the reconditioning and care of oiled furniture, stairs, wood, parquet and cork flooring. It is equally suitable for factory-oiled surfaces (preliminary test required). The wood care oil has both a regenerating and care effect, levels out smaller defects and gives the wood back its beauty and brilliance. It is anti-static and provides a reliable protection against water and dirt. It can be applied on the entire surface as well as partially. While OLI-NATURA Wood Care Oil ‘Nature’ is used for uncoloured oiled surfaces, OLI-NATURA Wood Care Oil ‘White’ is applied on white oiled ones.
Tip: If the floor or the furniture has been treated on the factory with a film-forming UV oil, the care oil can not penetrate into the wood. In case of doubt, simply place a sample surface in a hidden place.
The product is free of biocidal substances, preservatives, cobalt and oxime. The fully hardened material is non-hazardous for humans, plants and animals. It is saliva and sweat proof according to DIN 53160 and meets the DIN EN 71-3 standard (safety of toys).
|Consumption:||10-20 g/sqm per application / 1 litre - 50-100 sqm.|
|Drying times:||12 Hours|
|*||At 20° C and 65 % relative humidity, depending on the type of floor covering and the absorbency of the substrate.|
DRY CLEANING: Daily cleaning of oiled / hard wax oil-treated floors should be carried out dry with a broom or vacuum cleaner, as sand and dust act like sandpaper and can cause fine scratches. Loose dust on furniture surfaces can be easily removed with a cloth.
WET CLEANING: For regular cleaning with water, the mild „OLI-NATURA wood soap“ is ideal. It is specifically designed for the needs of oiled / hard wax oil-treated hardwood floors, floorboards, wooden stairs and furniture surfaces, and ensures rapid cleanliness and restoration of oil without leaching or attacking the wood.
APPLICATION: Shake well before use! Pour OLI-NATURA wood soap at a ratio of 1:200 into lukewarm water, wipe surface and leave to dry. Finished! For stubborn stains, do not dilute before use. Wipe off with water afterwards. Mixture: 25 ml to 5 litres / 50 ml to 10 litres.
RESTORATIVE TREATMENT AND MAINTENANCE: From time to time the oiled or hard wax oil-treated wood should be given some restorative treatment and maintenance. This will renew the protective effect and buff out slight scratches. Previously hard wax oil-treated surfaces should be treated at regular intervals with „OLI-NATURA wood care wax“. Oiled wood, however, should be restored with „OLI-NATURA wood care oil“. The entire surface can be treated, but it is also possible to treat only specific areas. After such treatment, the wood is anti-static and thus attracts little dust.
APPLICATION: The surface must be totally clean, dry, and free from dust and grease before treatment.
1.1 Full-surface restorative treatment for parquet: Apply approximately 10-20 g/m² (50-100 m²/l) of OLI-NATURA wood care oil or wood care wax thinly and evenly with a mop or a sprayer; allow to take effect for a short time (max. 10 minutes) and polish in with a white pad by hand or with a polishing machine. 1.2. Partial restorative treatment for parquet: Soak a white pad with wood care oil or wood care wax (10-20 g / m²) and rub in. Remove any excess with a dry cotton cloth after a maximum of 10 minutes.
2.0. Restorative treatment for stairs: Soak a white pad with OLI-NATURA wood care oil or wood care wax (10-20 g / m²) and rub in. Remove any excess with a dry cotton cloth after a maximum of 10 minutes.
3.0. Restorative treatment for furniture: Pour OLI-NATURA wood care oil or wood care wax onto a clean, lint-free cotton cloth and apply evenly and thinly along the grain. Remove any excess with a dry cotton cloth after a maximum of 10 minutes.
Note: Let the impregnated surface dry for a minimum of 12 hours, preferably overnight. Do not wet wipe for the first few days. In the case of sensitive surfaces, test first on an inconspicuous area.
Important: Oil soaked cloths / pads may spontaneously combust due to heat accumulation. They should therefore be cleaned or soaked in water immediately after use.