New product
Size of trading unit: 0,25L; 1L
For refreshing and maintenance of all natural and white indoor oil treated wood surfaces.
Consumption: Depending on the area of application and absorptivity of the substrate: 10-20 g/sqm per application / 1 litre is sufficient for circa 50-100 sqm.
in Stock
Warning: Last items in stock!
Availability date:
For refreshing and maintenance of all natural and white indoor oil treated wood surfaces
OLI-NATURA Care Oil is specifically designed for the reconditioning and care of oiled furniture, stairs, wood, parquet and cork flooring. It is equally suitable for factory-oiled surfaces (preliminary test required). The wood care oil has both a regenerating and care effect, levels out smaller defects and gives the wood back its beauty and brilliance. It is anti-static and provides a reliable protection against water and dirt. It can be applied on the entire surface as well as partially. While OLI-NATURA Wood Care Oil ‘Nature’ is used for uncoloured oiled surfaces, OLI-NATURA Wood Care Oil ‘White’ is applied on white oiled ones.
Tip: If the floor or the furniture has been treated on the factory with a film-forming UV oil, the care oil can not penetrate into the wood. In case of doubt, simply place a sample surface in a hidden place.
The product is free of biocidal substances, preservatives, cobalt and oxime. The fully hardened material is non-hazardous for humans, plants and animals. It is saliva and sweat proof according to DIN 53160 and meets the DIN EN 71-3 standard (safety of toys).
Consumption: | 10-20 g/sqm per application / 1 litre - 50-100 sqm. |
Drying times: | 12 Hours |
* | At 20° C and 65 % relative humidity, depending on the type of floor covering and the absorbency of the substrate. |
Manufacturer: | OLI Natura |
DRY CLEANING: Daily cleaning of oiled / hard wax oil-treated floors should be carried out dry with a broom or vacuum cleaner, as sand and dust act like sandpaper and can cause fine scratches. Loose dust on furniture surfaces can be easily removed with a cloth.
WET CLEANING: For regular cleaning with water, the mild „OLI-NATURA wood soap“ is ideal. It is specifically designed for the needs of oiled / hard wax oil-treated hardwood floors, floorboards, wooden stairs and furniture surfaces, and ensures rapid cleanliness and restoration of oil without leaching or attacking the wood.
APPLICATION: Shake well before use! Pour OLI-NATURA wood soap at a ratio of 1:200 into lukewarm water, wipe surface and leave to dry. Finished! For stubborn stains, do not dilute before use. Wipe off with water afterwards. Mixture: 25 ml to 5 litres / 50 ml to 10 litres.
RESTORATIVE TREATMENT AND MAINTENANCE: From time to time the oiled or hard wax oil-treated wood should be given some restorative treatment and maintenance. This will renew the protective effect and buff out slight scratches. Previously hard wax oil-treated surfaces should be treated at regular intervals with „OLI-NATURA wood care wax“. Oiled wood, however, should be restored with „OLI-NATURA wood care oil“. The entire surface can be treated, but it is also possible to treat only specific areas. After such treatment, the wood is anti-static and thus attracts little dust.
APPLICATION: The surface must be totally clean, dry, and free from dust and grease before treatment.
1.1 Full-surface restorative treatment for parquet: Apply approximately 10-20 g/m² (50-100 m²/l) of OLI-NATURA wood care oil or wood care wax thinly and evenly with a mop or a sprayer; allow to take effect for a short time (max. 10 minutes) and polish in with a white pad by hand or with a polishing machine. 1.2. Partial restorative treatment for parquet: Soak a white pad with wood care oil or wood care wax (10-20 g / m²) and rub in. Remove any excess with a dry cotton cloth after a maximum of 10 minutes.
2.0. Restorative treatment for stairs: Soak a white pad with OLI-NATURA wood care oil or wood care wax (10-20 g / m²) and rub in. Remove any excess with a dry cotton cloth after a maximum of 10 minutes.
3.0. Restorative treatment for furniture: Pour OLI-NATURA wood care oil or wood care wax onto a clean, lint-free cotton cloth and apply evenly and thinly along the grain. Remove any excess with a dry cotton cloth after a maximum of 10 minutes.
Note: Let the impregnated surface dry for a minimum of 12 hours, preferably overnight. Do not wet wipe for the first few days. In the case of sensitive surfaces, test first on an inconspicuous area.
Important: Oil soaked cloths / pads may spontaneously combust due to heat accumulation. They should therefore be cleaned or soaked in water immediately after use.
Rip-resistant cotton cloths for oiling,...
3,25 EUR
Size of trading unit: 0,25L; 1L For...
21,95 EUR
Size of trading unit: 0,25L, 1L, 2,5L...
26,95 EUR
21,90 EUR
105,90 EUR
178,00 EUR
33,90 EUR
38,95 EUR
26,95 EUR
34,90 EUR
39,90 EUR
21,95 EUR
16,90 EUR
36,90 EUR
43,90 EUR
19,90 EUR
150,80 EUR
61,40 EUR
32,95 EUR
112,22 EUR
42,94 EUR
19,99 EUR